SA Series 150V Piezo Stack Actuators
The PiezoDrive SA stack actuators are high-performance piezoelectric stack actuators with a UV cured epoxy coating for improved mechanical and humidity protection. The SA actuators are matched to the range of PiezoDrive amplifiers and driver modules. Applications include: Nanopositioning, Microscopy, Precision Machining, Vibration Control, Hydraulic Pumps, Valves, and Optics.
Specifications
Order Code |
Range +/-10% |
Length | Cross Section |
Cap. +/-20% |
Mass | Blocking Force |
Stiffness | Res. Freq. |
$AU | Buy Now |
SA030305 | 5.6um | 5mm | 3x3mm | 140nF | 0.53g | 330N | 80N/um | 300kHz | $AU35 | Buy Now |
SA030306 | 7.0um | 6mm | 3x3mm | 180nF | 0.6g | 330N | 66N/um | 250kHz | $AU35 | Buy Now |
SA030310 | 14um | 10mm | 3x3mm | 300nF | 1.1g | 330N | 33N/um | 150kHz | $AU56 | Buy Now |
SA030318 | 25um | 18mm | 3x3mm | 500nF | 2.0g | 330N | 18N/um | 83kHz | $AU79 | Buy Now |
SA050510 | 14um | 10mm | 5x5mm | 630nF | 2.0g | 900N | 108N/um | 150kHz | $AU52 | Buy Now |
SA050520 | 31um | 20mm | 5x5mm | 1.8uF | 4.0g | 900N | 41N/m | 74kHz | $AU93 | Buy Now |
SA050536 | 56um | 36mm | 5x5mm | 4.3uF | 7.1g | 900N | 28N/um | 42kHz | $AU163 | Buy Now |
SA070718 | 28um | 18mm | 7x7mm | 4.1uF | 7.0g | 1800N | 120N/um | 83kHz | $AU106 | Buy Now |
SA070742 | 70um | 42mm | 7x7mm | 10uF | 15g | 1800N | 51N/um | 36kHz | $AU226 | Buy Now |
External Insulation
The SA actuators can be supplied with a thermoplastic sleeve which provides additional mechanical protection and insulates the electrode contacts. For this option, add “-B” to the part number, e.g., “SA050510-B”. Minimum order quantities and lead-times apply, except for the SA050510-B and SA050536-B which are available from stock.
Mounting
Stack actuators should not be exposed to significant tensile loads, unequally distributed loads, off-axis loads, bending moments, or torque. To reduce mounting errors, a ceramic or stainless steel ball end can be used to interface the stack actuator to the load. Flexural mechanisms are also recommended.
Suitable adhesives for low temperature operation include cyanoacrylate, e.g. superglue gel, and general-purpose two-part epoxies, e.g. Loctite 3430. In applications where heat dissipation or operation at elevated temperature is required, Loctite 9466 is recommended.
The maximum recommended tensile load is 10% of the blocking force. In applications that require bi-directional forces or high-speed motion, a preload force is recommended with a magnitude greater than the maximum tensile load. This guarantees that the actuator is always in compression. The maximum recommended preload is 50% of the blocking force.
Ball Ends
PiezoDrive stack actuators can be supplied with ceramic ball ends to improve the load distribution, simplify the mounting, and reduce bending moments during service. One or two ball ends can be specified by adding one of the following suffixes to the order code: -TBE (Top Ball End), -BBE (Bottom Ball End), or -2BE (Both Ball Ends). E.g. SA070718-2BE.
Actuator Width |
Ball End Diameter |
Additional Length |
3 mm | 3 mm | 3 mm |
5 mm | 5 mm | 5 mm |
7 mm | 6.5 mm | 6.5 mm |
Range
The range is specified for an applied voltage of -30V to +150V. If the input voltage is unipolar (0V to +150V) the specified range is reduced by a factor of 0.75. When a stack actuator is driving a stiff spring, the range is reduced by the factor
$$\frac{k_p}{k_p+k_L}$$ where \(k_p\) is the actuator stiffness and \(k_L\) is the load stiffness.
The travel range can also be reduced by restraining the end plates, e.g. by bonding the actuator to a stiff base. This effect is most significant in actuators that have a length less than twice the width.
Capacitance
The actuator capacitance is the small-signal capacitance measured at room temperature. Due to hysteresis, the effective capacitance increases with applied voltage. When operating at full range, the effective capacitance is approximately twice the small-signal capacitance. The capacitance also increases with temperature. A temperature increase of approximately 50 degrees C will double the effective capacitance.
Thermal
Piezoelectric actuators dissipate heat when driven at full range with a high frequency. PiezoDrive actuators can be operated continuously at temperatures up to 85 degrees C. Continuous operation beyond this temperature may damage the actuator.
The dissipated heat is approximately 10% of the applied electrical power. For a sine-wave, the applied electrical power is:
$$P = \frac{V_{p-p}^2 \pi C f}{4}.$$
Electrical Current Requirements
The required current is \( I = C~ dV/dt \) where \( I \) is the current, \( C \) is the effective capacitance, and \( dV/dt \) is the voltage rate of change. For a sine-wave, the required peak current is equal to:
$$ I_p = 2 \pi f V_{p-p} $$ where \( V_{p-p} \) is the peak-to-peak voltage. For a triangle wave, the required peak current is equal to:
$$ I_p = 2 C f V_{p-p} .$$
Recommended Drivers
Connecting Wires
All of the connecting wires are 100mm AWG26 PTFE insulated wires, except for the SA030306 actuator which has 15mm leads. Other lengths are available on request. Red identifies the positive terminal.
Vacuum Compatibility
The SA Actuators are supplied with a UV cured epoxy coating, with or without a thermoplastic sleeve. Both coatings and the wiring insulation meet the outgassing requirements for NASA SP-R-0022A.
Options / OEM Customization
- Ceramic ball ends (Order suffix – 2BE)
- Custom range and dimensions
- Custom wiring arrangement / connectors
- Preload or mechanical amplifier mechanisms
Dimensions
The total stack dimensions are based on the width and length of the ceramic listed in the specifications. The length specification includes the piezoelectric stack and two 1-mm thick ceramic end plates.
Piezoelectric Properties
The piezoelectric material is similar to PZT-5H and Navy Type VI.
Property | Symbol | Value | Unit |
---|---|---|---|
Piezoelectric constants | d_{33} | 600 | 10^{-12} m/V |
d_{31} | -270 | 10^{-12} m/V | |
g_{33} | 19.4 | 10^{-3} Vm/N | |
g_{31} | -9.2 | 10^{-3} Vm/N | |
Electro-mechanical coupling coefficients | K_{p} | 0.65 | NA |
K_{t} | 0.37 | NA | |
K_{31} | 0.38 | NA | |
Frequency constant | N_{p} | 1980 | Hz-m |
N_{t} | 1950 | Hz-m | |
N_{31} | 1450 | Hz-m | |
Elastic constant | Y_{33} | 5.3 | 10^{10} N/m^{2} |
Y_{11} | 7.2 | 10^{10} N/m^{2} | |
Q Factor | Qm | 80 | NA |
Dielectric constant | e_{33} ⁄ e_{0} | 3500 | @1 kHz |
Dissipation factor | tan δ | 2.5 | % @ 1 kHz |
Currie Temperature | T_{c} | 220 | C |
Density | ρ | 7.8 | g/cm^{3} |