PDu150CL – Low Noise 150V Piezo Driver with Strain Gauge Feedback

The PDu150CL combines a high-voltage power supply, precision strain conditioning circuit, feedback controller, and ultra-low noise amplifier (26uV RMS) into a package the size of a credit card. It provides all of the necessary functions for high-resolution open-loop or closed-loop control of piezoelectric actuators with or without integrated resistive strain sensors. The PDu150CL develops up to 300mA of output current at frequencies up to 80 kHz with very low noise. It is suited to demanding applications such as semiconductor machinery, scanning probe microscopy, optics, vibration control, and nanopositioning. The PDu150CL can be purchased as a calibrated pair with an SCL Series Closed-Loop Stack Actuator.

The PDu150CL is protected against short-circuit, average current overload, and excessive temperature. Passive cooling is available for low power applications or the integrated fan can be used when power dissipation is above 5W. The PDu150CL can be mounted with four M2.5 screws or directly to a host motherboard (PDu150CL-PCB).

PDu150CL Low Noise 150V Piezo Driver with Strain Gauge Feedback
  • Download Datasheet
  • SCL Series Closed-Loop Stack Actuators
  • Enquiry

    • Quotes Requests can be downloaded by adding products to the online cart, then choosing “Download Instant Quote” during checkout, or contact us.

      Response Times are typically 2-3 days for non-technical enquiries, and 3-14 days for technical enquiries. We apologize for the delay during busy times.


    • This field is for validation purposes and should be left unchanged.


  • Obtain instant quote

    • Click Buy Now
    • Select desired options
    • Add to cart
    • Proceed to checkout
    • Enter details
    • Download instant quote

Specifications

Power Supply +24 V (+/-10%)
Output Voltage -30 V to +150 V
Peak Current 300 mA
RMS Current 235 mA
Power Bandwidth 80 kHz (150 Vp-p)
Signal Bandwidth 180 kHz
Slew Rate 38 V/us
Gain 20 V/V
Input Impedance 10 kOhm (Closed loop mode)
Input Impedance 3.05 kOhm (Open loop mode)
Input Offset +/- 5 mV
Load Unlimited
Output Noise 26 uV RMS (1 uF load, 0.03 Hz to 1 MHz)
Protection Short circuit, over-current, and temperature
Quiescent Current 100 mA (10 mA in shutdown)
Connectors Screw terminals (AWG 20-30)
Dimensions 89 x 40 x 44 mm (L x W x H)
Environment 0C to 60C (32F to 140F)
Weight 80 gram

Connection Diagram

Recommended driver circuit for closed-loop stack actuators
Pin Function
VS Power Supply (+24V)
G Ground
EN Enable
IN Signal Input
SNS Sensor Output
S-, S+ Bridge Sensor Connections
B-, B+ Bridge Drive Connections
HV-, HV+ High Voltage Output

Operation

PDu150CL - Low Noise 150V Piezo Driver with Strain Gauge Feedback -

PDu150CL Block Diagram

The PDu150CL can be used in either open-loop or closed-loop modes. In the open-loop mode, the input signal is connected directly to the power amplifier. Note that the amplifier outputs use a novel low-noise differential architecture that cannot be connected to ground, for example, to the ground lead of an earthed oscilloscope.

In the closed-loop mode, the input signal acts as a command signal for the feedback loop. The strain signal is derived from a resistive strain gauge attached to the piezo or structure.

Output Current

The peak output current is 300mA. In addition, the maximum average current is 105mA per amplifier. The average current is useful for calculating the power dissipation and average supply current. For a sine wave, the average positive output current is equal to $$ I_{av} = \frac{ \sqrt{2} }{ \pi } I_{rms} = \frac{1}{\pi} I_{pk}. $$

Supply Current

The quiescent power for the amplifier is approximately 2 W or 85 mA. This can be reduced to <10 mA by pulling the Enable pin low with an open collector circuit. If the fan is used, the quiescent power is increased by 0.5W,

$$ I_s= \frac{200 \times \left( I_{av} + 0.010 \right)}{24} $$ where \(I_{av}\) is the total average output current. The maximum supply current is 0.9A at full power.

Power Bandwidth

The power bandwidth is the maximum frequency periodic signal that can be reproduced without distortion. The calculator determines the maximum operating frequency and required power for a given load capacitance. The calculator includes the effects of current limit, slew-rate, output impedance, and signal bandwidth. The calculator does not include the time-constant of the peak current limit, and may be inaccurate when the power bandwidth is below 100 Hz.

The nominal slew-rate of the PDu150CL is 38 V/us. Therefore, the maximum frequency sine-wave is $$ f_{max}= \frac{38 \times 10^6}{\pi~V_{L(p-p)}} $$ Therefore, the maximum frequency for a 150 Vp-p sine-wave is 80 kHz.

With a capacitive load, the power bandwidth is limited by the output current. The maximum frequency sine wave is $$ f_{pwr} = \frac{I_{pk}}{\pi V_{L(p-p)}~C_L} $$ where \(I_{pk}\) is the peak current limit, \(V_{L(p-p)}\) is the peak-to-peak output voltage, and \(C_L\) is the effective load capacitance.

Small Signal Bandwidth

PDu150CL Signal Bandwidth - Small Signal Frequency Response

Small Signal Frequency Response

Load Capacitance Bandwidth
No Load 180 kHz
30 nF 120 kHz
100 nF 34 kHz
300 nF 11 kHz
1 uF 3.2 kHz
3 uF 980 Hz
10 uF 190 Hz
30 uF 73 Hz

Small Signal Bandwidth (-3dB)

Power Amplifier Noise

The output noise contains a low frequency component (0.03 Hz to 10 Hz) that is independent of the load capacitance; and a high frequency component (10 Hz to 1 MHz) that is inversely related to the load capacitance. Optimal noise performance is achieved with passive cooling as magnetic fields from the fan can induce mV level interference in the outputs. In low noise applications, where the fan is removed, some external air-flow is required if the power dissipation is above 5W, refer to Heat Dissipation.

The noise is measured with an SR560 low-noise amplifier (Gain = 1000), oscilloscope, and Agilent 34461A Voltmeter. The low-frequency noise is plotted below. The RMS value is 15 uV with a peak-to-peak voltage of 100 uV.

PDu150CL Low Frequency Noise from 0.03 Hz to 10 Hz

Low Frequency Noise from 0.03 Hz to 10 Hz.

The high frequency noise (10 Hz to 1 MHz) is listed in the table below versus load capacitance. The total noise from 0.03 Hz to 1 MHz can be found by square summing the RMS values, that is $$ \sigma = \sqrt{ \sigma_{LF}^2 + \sigma_{HF}^2 } .$$

Load
Capacitance
High Frequency
Noise RMS
Total Noise
RMS
10 nF 450 uV 450 uV
30 nF 170 uV 171 uV
100 nF 60 uV 62 uV
300 nF 34 uV 37 uV
1 uF 21 uV 26 uV
3 uF 16 uV 23 uV
10 uF 16 uV 22 uV
30 uF 18 uV 23 uV

High Frequency Noise (10 Hz to 1 MHz) and
Total Noise (0.03 Hz to 1 MHz)

Strain Sensor Specifications

Strain Sensor Specifications
Bridge Excitation 6V (Differential)
Sensor Resistance 350 Ohm to 1000 Ohm
Sensor Configuration Single, Half, or Full Bridge
Bridge Balance Range +/-6 mV
Gain Range 200 to 3000
Offset Range +/-6 mV
Bandwidth 10 kHz
Input Noise Voltage 3 uV RMS (0.1 Hz to 100 Hz

Sensor Connection

The PDu150CL is compatible with single element strain sensors, half-bridges, and full-bridge sensor arrangements. The advantages of these different arrangements and the recommended methods of connection are described in the following. Suitable strain sensors are available from many suppliers, including www.omega.com. The PDu150CL can be purchased as a calibrated pair with an SCL Series Closed-Loop Stack Actuator.

Single Element Strain Gauge

Single element strain sensors can be useful in applications where the temperature is stable or simplicity is a priority. As shown below, the recommended configuration requires three dummy resistors (R) equal in resistance to the strain gauge. The best temperature stability is achieved when the dummy resistors have the same temperature coefficient as the strain gauge and are thermally connected to the strain gauge.

PDu150CL - Low Noise 150V Piezo Driver with Strain Gauge Feedback -

Half Bridge Strain Sensor

A half bridge arrangement with a 90 degree rosette sensor provides good immunity to temperature variation and approximately 30% better resolution than a single element. The recommended configuration requires two dummy resistors (R) that are equal in value to the strain gauge resistance.

PDu150CL - Low Noise 150V Piezo Driver with Strain Gauge Feedback -

The strain element aligned to the piezo expansion is denoted by (\(+\varepsilon\)) and the 90 degree element is denoted (\(-\nu\varepsilon\)). This convention is adopted since a positive strain in the piezo \(+\varepsilon\) causes a negative resistance change in the 90 degree element due to Poisson’s ratio (\(\nu\)).

Full Bridge Strain Sensor

A full-bridge arrangement constructed from two 90 degree rosette sensors provides good immunity to temperature variation, the best linearity, and twice the resolution of a half bridge; however, this configuration also requires more wiring. The PDu150CL can be purchased as a calibrated pair with an SCL Series Closed-Loop Stack Actuator.

Piezoelectric stack actuator with strain gauge
PDu150CL - Low Noise 150V Piezo Driver with Strain Gauge Feedback -

The strain element aligned to the piezo expansion is denoted by (\(+\varepsilon\)) and the 90 degree element is denoted (\(-\nu\varepsilon\)). This convention is adopted since a positive strain in the piezo \(+\varepsilon\) causes a negative resistance change in the 90 degree element due to Poisson’s ratio (\(\nu\)).

Sensor Noise and Resolution

Since the sensor noise is filtered by the complementary sensitivity function of the control loop, the bandwidth of interest is typically 0.1Hz to 100Hz. The upper frequency limit has little effect since the majority of noise in this bandwidth is due to low-frequency noise from the on-board references and primary gain stage. With a bridge resistance of 350 Ohms, the total input referred noise voltage is plotted below, the RMS value is 3uV with a peak-to-peak voltage of 20uV.

PDu150CL Total Strain Noise with a 350 Ohm Bridge (0.1Hz to 100Hz)

Total Strain Noise with a 350 Ohm Bridge (0.1Hz to 100Hz)

The sensor noise can be used to estimate the sensor resolution. The induced voltage for a two-varying element full bridge is [1, 2]

$$ V_s = \frac{1}{2} V_e~GF~\varepsilon~(1+\nu)$$ Where \(V_e\) is the excitation voltage (5V), GF is the gauge factor (typically ~2), \(\varepsilon\) is the strain, and \(\nu\) is the Poisson’s ratio (0.34 for PZT5H). For a full-scale strain of 0.1%, the expected bridge voltage is 6.7 mV. Therefore, the expected RMS resolution is $$ \text{Resolution} = \frac{3~\text{uV}}{6.7~\text{mV}} =0.045\%~\text{of Full Scale} $$

Sensor Calibration Procedure

The following procedures are required to calibrate the bridge conditioning circuit and should be performed with the sensor and piezo connected to the PDu150CL.

Balance the Bridge

Small mismatches in the bridge resistances can be accounted for by the Bridge Balance pot. This step optimizes the temperature sensitivity of the bridge circuit.

1) Place the PDu150CL in Open-Loop mode and apply 0V or a short-circuit to the input terminals.

2) Connect a voltmeter between the S- and S+ terminals (without disconnecting the bridge).

3) Tune the Bridge Balance pot until the measured voltage is zero.

Set the Sensitivity and Offset

This step calibrates the sensor so that a 0V to 150V signal applied to the piezo produces a 0V to 10V strain signal.

1) Turn the Sensor Gain pot fully anti-clockwise, (10 turns).

2) Ensure the PDu150CL is in Open-Loop mode and apply 0V or a short-circuit to the input terminals.

3) Monitor the SNS terminal and tune the Sensor Offset pot until the voltage is zero.

4) Apply 7.5V to the input terminal to generate 150V across the piezo.

5) Monitor the SNS terminal and tune the Sensor Gain pot until the voltage is +10V.

Variations

Many variations of the above procedure are possible. Some useful options are listed below.

The offset and gain can be tuned simultaneously by applying a 5-Hz sine wave to the input terminals with a range of 0V to 7.5V, which results in 0V to 150V across the piezo. Monitor the SNS terminal with an oscilloscope and tune the Sensor Offset and Sensor Gain pots until the measured sine-wave is between 0V and 10V.

Rather than calibrating the sensor to +10V at full scale, another voltage such as +5V may be more desirable.

If negative voltages across the piezo are acceptable, it is convenient to calibrate the full piezo voltage range, e.g. -30V to +150V, to a SNS voltage of 0V to +10V. This requires an input of -1.5V to +7.5V during calibration, rather than 0V to +7.5V.

For stack actuators with different voltage ratings, the calibration input signal should be chosen accordingly. For example, a suitable calibration input for a piezo with a voltage rating -20V to +100V would be -1V to +5V.

Closed-Loop Operation

Once the sensor is calibrated, the PDu150CL can be placed in closed-loop mode. The structure of the closed-loop system is illustrated below.

PDu150CL - Low Noise 150V Piezo Driver with Strain Gauge Feedback -

Feedback Structure of the PDu150CL

The closed-loop sensitivity is defined by the sensitivity of the strain sensor. For example, if the piezo has a full-scale range (FSR) of 20 um and the strain sensor is calibrated for 0V to 10V, the closed loop sensitivity is $$ \text{Sensitivity} = \frac{\text{FSR}}{10~\text{V}} = 2~\text{um/V} $$

Calibrating the Feedback Gain

The feedback gain defines the closed-loop bandwidth and settling time of the system. It is usually advantageous to choose the lowest satisfactory feedback gain to avoid unnecessary sensor noise. A simple calibration procedure is described in the following:

1) Turn the Feedback Gain pot fully anti-clockwise (10 turns).

2) Place the PDu150CL in closed-loop mode and apply a 1Vp-p triangle wave with a 5V offset to the input terminal. If the sensor was calibrated with a full scale range other than 10V, use an offset voltage equal to mid-range.

3) Monitor the input signal and SNS terminal with an oscilloscope and increase the feedback gain until the point where overshoot begins to occur.

For applications that do not require high-speed tracking, the above procedure is not required. The minimum feedback gain is suitable.

To achieve a specific -3dB bandwidth, replace the triangle wave with a sine-wave and tune the feedback gain until the amplitude of the SNS signal is 0.7 Vp-p.

Headroom

When the full-scale range of the sensor is calibrated to the full-scale range of the piezo, some consideration for ‘headroom’ is required. To allow the control loop to compensate for effects such as thermal drift and creep, the input signal is typically restricted to a range of 10% to 90% so that the control-loop can utilize the remaining 10% at the lower and upper extremes. For example, a system with a full-scale range of 0V to 10V, would have a practical closed-loop input range of 1V to 9V.

An alternative to the above approach is to account for headroom during calibration. For example, rather than using the full scale range for calibration, e.g. -30V to +150V, a smaller range can be chosen, e.g. -15V to +130V. By using this method, the resulting closed-loop input range will be 0V to 10V, which may be more desirable than 1V to 9V.

Example Application

In this example, the piezoelectric stack actuator pictured below (SCL050518) is operated in closed-loop. The actuator develops a displacement of 20um at 150V and utilizes a full-bridge strain sensor constructed from two 90 degree rosettes.

Piezoelectric stack actuator with strain gauge

The PDu150CL was calibrated so that an applied voltage of 0V to 150V corresponds to a strain signal of 0V to 10V. The feedback gain was then chosen to achieve good tracking performance with a 10-Hz full-range triangle wave, as shown below.

PDu150CL Example Tracking

10-Hz Full-Range Tracking Performance

The open- and closed-loop responses to a full-range 1-Hz sine-wave input are plotted below. Excellent compensation of hysteresis can be observed.

PDu150CL Open and Closed-Loop response (1-Hz Sinusoid)

Open and Closed-Loop response (1-Hz Sinusoid)

Before evaluating the total positioning noise, the feedback gain is adjusted to provide a closed-loop bandwidth of precisely 20 Hz by applying a 20-Hz sine-wave and varying the feedback gain until the amplitude response is -3dB. This allows a direct comparison to other methods with an identical bandwidth.

The total positioning noise due to the amplifier, sensor, and feedback controller can then be quantified by measuring the differential output voltage of the power amplifier with a zero volt input [3].

The differential output voltage was measured using an SR560 low-noise amplifier with a gain of 10 and a passband of 0.03 Hz to 1 MHz. The resulting voltage was scaled by the sensitivity of the piezo (20um/150V) and is plotted below. The RMS value is 8.8 nm with a peak-to-peak value of 60 nm over 50 seconds. This represents an RMS resolution of $$ \text{Resolution} = \frac{8.8~\text{nm}}{20~\text{um}} =0.044\%~\text{of Full Scale} $$

This value agrees with the predicted resolution in “Sensor Noise and Resolution”.

PDu150CL Closed-loop Positioning Noise (0.03Hz to 1MHz)

Closed-loop Positioning Noise (0.03Hz to 1MHz)

Overload Protection / Shutdown

The PDu150 is protected against short-circuit and average current overload.

The amplifier can be shutdown manually by pulling the Enable pin low with an open-collector, or open-drain circuit. The Enable pin normally floats at 5V and should not be driven directly.

Heat Dissipation

The heat dissipation is approximately $$ P_d = 200 \times \left( I_{av} + 0.010 \right) $$

For example, with a sinusoidal output, the power is $$ P_d = 200 \times \left( V_{L(p-p)} C_L f + 0.010 \right) $$

A straight-forward method for measuring heat-dissipation is to measure the supply current with a multimeter during operation. The heat dissipation is equal to the product of DC current and voltage.

In low-noise and low-power applications where it is desirable to remove the fan, natural convection is sufficient if the heat dissipation is less than 5W. If the heat dissipation is above 5W, an external air-flow of 5 CFM is recommended. To avoid interference, external fans should be located further than 80mm from the module.

Safety

This device produces hazardous potentials and should be used by suitably qualified personnel. Do not operate the device when there are exposed conductors. Parts of the circuit may store charge so precautions must also be taken when the device is not powered.

Previous Versions

Hardware Version Manufactured Manual
V5 2017-2023 Download Datasheet
V4 2016-2017 Download Datasheet

References

[1] A Review of Nanometer Resolution Position Sensors: Operation and Performance; A. J. Fleming; Sensors and Actuators A: Physical; 2013, 190, 106-126

[2] Design, Modeling and Control of Nanopositioning Systems; A. J. Fleming & K. K. Leang; Springer, 2014

[3] Measuring and Predicting Resolution in Nanopositioning Systems; A. J. Fleming; Mechatronics; 2014, 24, 605-618

Dimensions

The mounting posts accept M2.5 screws.

The PCB mounting version (PDu150CL-PCB) is designed to be mounted onto a host motherboard. The only difference is the screw terminals are replaced by headers (Harwin M20-9990645 and M20-9990845) mounted on the bottom side of the module. The recommended PCB hole size for the pins is 1 mm. An Altium schematic and footprint library is available for download.

Click here to download 3D model

PDu150CL - Low Noise 150V Piezo Driver with Strain Gauge Feedback -
PDu150CL Dimensions (mm)